Hangzhou diaphragm coupling
Hangzhou drum gear coupling
Hangzhou plum blossom-shaped elastic coupling
Hangzhou star coupling
Hangzhou elastic pin coupling
Hangzhou elastic pin gear coupling
Hangzhou elastic sleeve pin coupling
Hangzhou JQ type clamp shell coupling
Hangzhou sprocket coupling
Hangzhou Slider Coupling
Hangzhou tire coupling
Hangzhou rigid coupling
Hangzhou serpentine spring coupling
Three-jaw coupling for Hangzhou pump
Hangzhou Coupling Accessories
Hangzhou Coupling Rough
Hangzhou LK elastic block coupling
Hangzhou WH type slider coupling
WH type slider coupling (JB/ZQ 4384-97 instead of JB/ZQ 4384-86, formerly known as KL) slider coupling is similar in structure to cross slider coupling, the difference is that the middle cross slider is square The sliding block uses the middle sliding block to slide in the corresponding radial grooves on the end faces of the coupling halves on both sides to realize the coupling of the two halves. The allowable compensation amount of the sliding block coupling: axial △ x=1~ 2mm, radial △y ≤ 0.2mm, angular △α≤ 40'.
WH type slider coupling (JB/ZQ 4384-97 replaces JB/ZQ 4384-86 formerly known as KL) The structure of the slider coupling is similar to the cross slider coupling, except that the middle cross slider is square The sliding block uses the middle sliding block to slide in the corresponding radial grooves on the end faces of the coupling halves on both sides to realize the coupling of the two coupling halves.This coupling has high noise, low efficiency and fast wear. Generally, it is not used as much as possible. It is only used for occasions with very low speed. The slider coupling specified in this standard is suitable for oil pump devices or other occasions with small transmission torque. Compensate the relative offset of the two axes, shock absorption and cushioning performance; its working temperature is -20~70°C.The nominal torque transmitted is 16~500N.m.
The basic parameters and main dimensions of WH type slider coupling:
model | Nominal torque Tn(Nm) | Allowable speed [n]r/min | Diameter of shaft hole | Length of shaft hole | D | D1 | B1 | B2 | l | Moment of inertia Kg.m2 | Mass kg | |
d1 d2 | Y | J1 | ||||||||||
L | ||||||||||||
mm | ||||||||||||
WH1 | 16 | 10000 | 10,11 12,14 | 25-32 | 22-27 | 40 | 30 | 52 | 13 | 5 | 0.0007 | 0.6 |
32-42 | 27-30 | |||||||||||
WH2 | 31.5 | 8200 | 12,12,16,(17),18 | 50 | 32 | 56 | 18 | 5 | 0.0038 | 1.5 | ||
WH3 | 63 | 7000 | 16,(17),18,20,22 | 42-52 | 30-38 | 70 | 40 | 60 | 18 | 5 | 0.0063 | 1.8 |
52-62 | 38-44 | |||||||||||
WH4 | 160 | 5700 | 20,22,24,25,28 | 80 | 50 | 64 | 18 | 8 | 0.013 | 2.5 | ||
WH5 | 280 | 4700 | 25,28,30,32,35 | 62-82 | 44-60 | 100 | 70 | 75 | 23 | 10 | 0.045 | 5.8 |
82-112 | 60-84 | |||||||||||
WH6 | 500 | 3800 | 30,32,35,38,40,42,45 | 120 | 80 | 90 | 33 | 15 | 0.12 | 9.5 | ||
WH7 | 900 | 3200 | 40,42,45,48,50,55 | 112 | 84 | 150 | 100 | 120 | 38 | 25 | 0.43 | 25 |
112-142 | 84-107 | |||||||||||
WH8 | 1800 | 2400 | 50,55,60,63,65,70 | 190 | 120 | 150 | 48 | 25 | 1.98 | 55 | ||
WH9 | 3550 | 1800 | 65,70,75,80,85 | 172-212 | 132-167 | 330 | 190 | 180 | 58 | 40 | 4.9 | 85 |
172-212 | 132-167 | |||||||||||
WH10 | 5000 | 1500 | 80,85,90,95,100 | 330 | 190 | 180 | 58 | 40 | 7.5 | 120 |
Hangzhou WH type slider coupling Hangzhou WH type slider coupling